Home » Picture Gallery, Telecommunication » IP67 D-SUB Connectors

IP67 D-SUB Connectors





 

For industrial use in harsh environments, connector systems are needed that meet special requirements.

Data communication and control systems do not stop at outdoor use. Connectors in the field have to cope with UV radiation, ozone, dry cold, damp heat, rain, snow, hail, freezing, dust, salt spray and wind load.

CONEC offers a large portfolio of water resistant D-SUB connectors and hoods with IP67 protection for these applications. The series are characterised by special sealing measures on the connector as well as on the sealing frame, the use of high-quality materials and a particularly robust design.

In the field of IP67 D-SUB connectors, CONEC not only offers a wide range of position numbers, mounting and termination variants, but also the option of choosing between 3 different types of housing depending on the application:

– Solid Body

– CONEC SlimCon

– Standard housing

The advantage of the Solid Body and CONEC SlimCon connector series are their one-piece zinc die-cast housing with nickel-plated surface, which ensures optimum protection for the system and is characterised by robustness. The CONEC SlimCon series also scores with its very small dimensions.

While the standard housing is sealed by the sealing frame, an O-ring is used in the Solid Body series. In the smallest IP67 D-SUB connector series, CONEC uses a flat seal.

IP67 D-SUB CONEC SlimCon connectors

… elegant, small and robust

IP67 D-SUB CONEC SlimCon connectors are available in housing sizes 1 to 3 as male and female versions and in the Standard, High Density and Combination series. Due to their very small design and the one-piece zinc die-cast housing, they are ideally designed for industrial and harsh environments where minimal installation space is available.

Compared to an IP67 protected connector with an extended sealing frame, a reduction of the occupied area of up to 52% is achieved. The size of the housing corresponds to the standard dimensions of a D-SUB connector, so a 1:1 conversion from IP20 to IP67 interfaces is also possible.

Four contact surfaces ensure that the connectors are always mounted evenly with the existing seal on the unit wall. Thus, excess pressure at the sealing is avoided and safe assembly at the customer�s is ensured. CONEC SlimCon connectors are designed for an wall thickness of 0.8 to 1.3 millimetres.

IP67 D-SUB CONEC Solid Body connectors

… robust, versatile and suitable for larger wall thicknesses

The IP67 D-SUB CONEC Solid Body connector series is available in housing sizes 1 to 5 as male and female versions. The one-piece zinc die-cast housing also makes this series suitable for industrial and harsh environments.

The connectors are designed for rear wall mounting and are euqipped with a 4-40 UNC internal thread. Corresponding threaded bolts are included as standard with the products. CONEC Solid Body connectors are available

from 09-pos to 25-pos. (Standard) and 15-pos to 78-pos. (High Density) and also in many combination layouts. Solid body connectors are suitable for wall thicknesses from 1.0 to 1.6 mm.

IP67 D-SUB Hoods

IP67 Hoods are available in housing sizes 1 to 5 and can accommodate various cables with a diameter of 7 to 16 mm, depending on the size.

In addition to a very compact hood, the portfolio also includes variants with a large interior and protective caps. The IP67 D-SUB hood versions are available shielded and unshielded – alternatively with short screw or jack screw.

CONEC IP67 D-SUB connectors are used, for example, in traffic safety. They ensure reliable signal transmission in camera systems of police motorcycles. In addition to resistance to weathering, vibration resistance is also important here.

IP67 D-SUB connectors from CONEC are also used in the field of agricultural technology. They guarantee secure data transmission in GPS systems for precise positioning of tractors or corresponding fertiliser, trailers/components. In railroad technology, IP67 D-SUB connectors are used in the field of mobile communication technology, e.g. in a control panel for analog and digital train radio, but also in mobile information systems and stationary radio stations.

When used in civil aviation, not only is there limited installation space available, but the connectors used must also meet particularly high quality requirements. Reliable signal transmission on autopilots with servo-motor components must

even in the event of thermal shocks.

Advantages:

One-piece zinc die-cast housing (Solid Body and CONEC SlimCon)

Space-saving design (CONEC SlimCon)

Low weight

1:1 conversion from IP20 to IP67 interface possible

Shock- und vibration resistant according to IEC60807-2 (CONEC SlimCon)

Suitable for harsh environments

Fields of application

Agricultural technology

Automation technology

Aviation

Communication technology

Drive Technology

Medical technology

Railroad technology

Safety and monitoring systems

For more than 40 years, CONEC Elektronische Bauelemente GmbH has been developing, producing and marketing high-quality connectors, patch cable and single ended cable as well as enclosure technology.

CONEC products are used in automation, telecommunications and energy technology, machine manufacturing, agriculture and medical technology, transportation and the aviation industry.

The headquarters in Lippstadt has a large research and development department, its own tool-making department, a CNC-turning department and a synthetics injection moulding plant.

As part of the Amphenol Group, CONEC participates in the growth and development opportunities of a globally active group and at the same time acts flexibly and quickly as a medium-sized company in order to optimally adapt to changing customer needs.

In addition to a variety of connectors for all current standards, our particular strength is the integrated moulding of components and assemblies and the development of customized solutions.

CONEC is a global player with its own subsidiaries and/or production sites in Canada, China, the Czech Reblublic, Poland and Slovakia.

The product portfolio includes connectors of the following categories:

• D-SUB/IP67 D-SUB Connectors

• IP67 RJ45 / USB / Mini USB / Fiber Optic LC Duplex

• CONEC Hybrid Connectors

• Connectors for agricultural and construction machines

• Circular Connectors

• PCB Connectors

• Customer specific solutions

The company�s quality management ensures high quality by applying the international standards according DIN EN ISO 9001. Depending on the product family, CONEC industrial connectors are tested and approved in accordance with UL, CSA or VDE.





Posted by on 5. May 2023. Filed under Picture Gallery, Telecommunication. You can follow any responses to this entry through the RSS 2.0. You can leave a response or trackback to this entry

You must be logged in to post a comment Login

Archive

Recent Comments

    © 2023 So-Co-IT. All Rights Reserved. Log in - Copyright by LayerMedia


    Blogverzeichnis - Blog Verzeichnis bloggerei.de Blog Top Liste - by TopBlogs.de Bloggeramt.de